Free tool · no sign-up

Delay & Reverb Time
Calculator

Delay, pre-delay and LFO times for any tempo. Plus handy info on when to not bother syncing.

  • Free
  • Runs in your browser
  • Phone friendly

Signal flow

Tap, Click, Create

Set Tempo

Type your BPM or tap it in time with the beat.

Pick A Unit

ms for plugins, whole ms for pedals, Hz for LFO or samples.

Copy & Paste

Click a value to copy it, then paste it in your DAW or plugin.

BPM → ms · Hz · samples

The full guide

User Manual

Set your tempo

Type your song’s BPM into the amber display. Decimals work too, like 87.5 or 128.5. Use the + and − keys to nudge it by 1 BPM, or click into the display and press the up and down arrows on your keyboard (hold Shift for 0.1 steps). Don’t know the tempo? Hit Tap (or press T) in time with the beat. After three taps the tool works out the BPM, and it ignores a missed tap.

Your DAW counts BPM in quarter notes, even in 6/8, so use the tempo your DAW shows.

Pick a unit

The switch bar changes every value in the table:

  • ms: milliseconds, to one decimal place. Use this for plugins.
  • Whole ms: rounded to the nearest millisecond, for pedals and fields that only take whole numbers.
  • Hz: one cycle per note, for LFOs, tremolo and auto-pan on gear without tempo sync.
  • Samples: for samplers and sample-accurate editors. Pick 44.1, 48 or 96 kHz under the bar.

Read the table and copy a value

Each row is a note length, from 4 bars down to 1/64. The columns are straight, dotted (1.5× as long) and triplet (2/3 as long). At 120 BPM a quarter note is 500 ms, a dotted eighth is 375 ms and an eighth-note triplet is 166.7 ms.

Click any number to copy it, then paste it into your plugin’s time field. A small pink ▲ means the value is beyond what a lot of hardware can do. In ms, it’s longer than many compact pedals allow (600 ms). In Hz, it’s outside the 0.1–20 Hz range many hardware LFOs cover.

Set your pre-delay

Pre-delay is the short gap before a reverb starts. The Pre-delay tab shows synced values from 1/128 to 1/16 at your tempo, plus a range bar. Around 10–40 ms keeps a vocal clear, and up to about 100 ms gives more separation.

More pre-delay doesn’t push a voice farther away. It keeps the dry voice clearer and closer, while the space around it sounds bigger. Synced values are a handy start, but many engineers simply set pre-delay in ms by ear. Values over 120 ms get a “long for a vocal” flag: that’s an effect, not a room.

More on this in our reverb cheat sheet.

Short delays you don’t sync

Slapback (70–150 ms), doubling (10–30 ms) and Haas widening (5–35 ms) are too short to be heard as rhythmic echoes, so they don’t need to follow the tempo. Set them by ear in ms. The classic tape slap was around 135 ms with no feedback. If you use a Haas delay for width, check your mix in mono, because parts can thin out or vanish.

Use the main table for echoes you want to hear as repeats. See our guide to the different types of delay.

Reverb tail and compressor release

The Tail & release tab shows note lengths at your tempo as reference lengths to listen against. They aren’t settings.

  • Reverb tail: set decay by ear so the tail fades out around the next hit, or the next bar for a lusher sound. The decay number on a reverb is often longer than the tail you actually hear in a busy mix, so typing “decay = one note” rarely sounds the way you’d expect. If the tail muddies the mix, gate it, duck it or automate it.
  • Compressor release: watch the gain-reduction meter and set release so it recovers just before the next hit. Auto release is a fine default. Release knobs work differently on every compressor, so a ms value is only a ballpark. Attack follows the transient, not the tempo.
  • Sidechain: the gap between kicks is one quarter note (468.8 ms at 128 BPM). Volume-shaper plugins sync to that length. A sidechain compressor’s release is usually much shorter, around 100–200 ms. Read more about sidechain compression.

Starting points and swing

The Starting points tab gives a few common places to start, each with its value at your tempo:

  • Vocal delay: a quarter note or a dotted eighth (an eighth for fast or busy songs).
  • Guitar and arps: a dotted eighth against played eighths gives that running-sixteenths sound.
  • Gate hold: 1/16 to 1/8, then shape the release by ear.

There are no genre presets, because no source backs a “correct” value per genre.

Using swung 16ths? Echoes on 1/8, 1/4, 1/2 and whole notes (and the longer dotted values) land back on the groove. Sixteenths, dotted eighths and triplets sit off the swing; use your delay’s swing or offset control if that bothers you.

Decode note labels in your DAW

Different DAWs and devices write the same note differently. A dotted eighth is 1/8D, 1/8. in Logic Echo, 1/8d in Replika, 3/16 as a fraction, and 3 steps in FL Studio’s Fruity Delay 3. An eighth-note triplet is 1/8T, 1/12 on Korg-style arps, and 8t on the Roland S-1. The Labels tab lists these, plus a fraction table for the other note values.

FAQ

Asked and answered

How do I calculate delay time from BPM?
Divide 60,000 by your BPM to get one beat (a quarter note) in milliseconds. At 120 BPM that’s 500 ms. Halve it for an eighth note (250 ms), multiply by 1.5 for dotted (375 ms) or by 2/3 for a triplet (166.7 ms).

What is a dotted eighth delay?
A delay of three sixteenth notes: 375 ms at 120 BPM. Against played eighth notes, its repeats fall between your notes and create a running-sixteenths rhythm, the sound The Edge made famous.

What’s the difference between dotted and triplet?
Dotted makes a note 1.5 times longer; triplet makes it 2/3 as long (three in the space of two). A dotted eighth (375 ms at 120 BPM) and an eighth-note triplet (166.7 ms) are very different lengths, so check which one your plugin is set to.

How much pre-delay should I use on vocals?
Around 10–40 ms keeps a vocal clear and up front. Go up to about 100 ms for more separation. A synced 1/64 or 1/32 is a handy start, then adjust by ear.

Should reverb decay match the tempo?
Not exactly. Let the tail fade out around the next hit (or bar) by ear. A reverb’s decay setting measures a longer fade than you’ll hear in a full mix, so “decay = one note length” is a rough guide at best.

Should I set compressor release to the tempo?
Use your ears and the gain-reduction meter: it should recover just before the next hit. Release controls behave differently on every compressor, so a note length in ms is only a ballpark. Auto release is a fine default.

How do I convert BPM to Hz for an LFO?
Divide 1,000 by the note length in ms. A quarter note at 120 BPM is 500 ms, so 2 Hz (two cycles per second). Pick Hz on the switch bar to see every note value in Hz. New to LFOs? Start with what an LFO is and how it works.

Why does my synced delay sound late?
The math is almost always right; the cause is usually latency. Check your DAW’s plugin delay compensation and plugin order, or the MIDI clock if you’re syncing hardware.

Does this work on my phone?
Yes. It’s free and runs in your browser on any device. Tap the TAP pad in time with your music, then tap a value to copy it.

Sounds for your Next Project

Sample packs and wavetables in the Producer Hive shop.

Melody To Chords Generator

Got a melody but stuck on chord progressions? Use our free tool.